Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="shiroitenshi" data-source="post: 1063333516" data-attributes="member: 27518">You can't increase torque on small CC, what you can do is increase the horsepower. B18cs are not really suited for extreme high rpm due to the sideloading they incur because of their rod stroke ratio. It is doable, but the engine won't last long.. so don't expect the 100,000km to be your next overhaul.. it will be less.. depending on how many times you hit 10Krpm. So if only occasional, why not?That's why B16B is a high revving monster.. with 1.84 r/s ratio, it does 10K rpm like b16A doing 9Krpm.. can last quite a long time.The main problem with pushing 10K is clearances. If you open up the stock B18c engine, you notice the piston sits about 1mm from the top of deck, so clearance should be enough.. but at high rpms, strange things start to happen... the 138mm rods start to become closer to 139mm.. and suddenly all the clearances measured earlier becomes not enough.That's why opt for custom rods and pistons, usually push the compression height to the most minimum so can stuff in longer rods. They also less likely to stretch under high rpm.Last part is the most important part.. The cams.. The tuner simply sets the fuelling and the ignition based on the hp they can get on the dyno.., so if not enough air going in the engine at high rpm, why would they want to add more fuel?I think people think cams are power makers because most high hp cars use it, but for vtec, even the stock cams (the vtec lobe) are quite high if you start comparing it to mitsus, toyota, etc, so everyone want to use without knowing what it's actually for.High rpm, the problem with engine breathing appears, resulting in torque loss. So to compensate that, we have to open the intake and exhaust valves longer by using higher duration cams. The thing with doing this is that it also reduces compression of the engine (dynamic compression, not static compression). That's why the higher duration cams require higher compression.. the cams will make the actual compression (dynamic compression) lower than it's static compression.So if a guy was playing with a B16A, what he would start to do with an adjustable cam pulley is open it by +1 intake -1 exhaust (increasing overlap by +2) and he would see that the torque loss is minimal even after 7.5K. (do note that you have to center the cams on true TDC before playing with the cam pulleys, you forget to do this, I won't take responsibility of you damaging your engine)If you already got the upgraded valvesprings to rev up to 9K, you should be able to break 170whp, even on standard B16A cams :PDo note that revving up to 9K requires that you tune the car... non rev cut ecus sometimes just use the same fuelling from 8K rpm straight to 9K, so at 9K, the engine runs lean.</blockquote>

Verification

The Marketplace Latest

Mitsubishi lancer Evo x front bumper
- Started by jeff6126
- Exterior and Body
Honda jazz fit gk flrs body kit
- Started by jeff6126
- Exterior and Body
Proton S70 body kit
- Started by jeff6126
- Exterior and Body
Proton saga BLM body kit
- Started by jeff6126
- Exterior and Body
Perodua bezza ~accident repair
- Started by jeff6126
- Exterior and Body
Mercedes Benz W205 C-class GT grille
- Started by jeff6126
- Exterior and Body
BMW E90 ~brake caliper spray ~rim spray
- Started by jeff6126
- Exterior and Body
Honda city gm6 FL front bumper
- Started by jeff6126
- Exterior and Body
original rare spec Rays Volk Racing RE30 15x7jj...
- Started by david tao
- Chassis and Wheels
original rare Rays Volk Racing TE37 SAGA S-Plus...
- Started by david tao
- Chassis and Wheels

Posts refresh every 5 minutes

Aventador stretching its legs at Sepang for the first time

https://www.zerotohundred.com/wp-content/uploads/2011/09/lambo-aventador-sepang-2-600x400.jpg

More pics of the Lambo Aventador this time. Sherman was there to witness the private debut event Lamborghini had...

Promotional / Sale Items

The forum is mainly for technical discussions or sharing of information and experience. It is not a war zone or flaming zone to run down each other.

For Sales items, kindly post your items and prices here ...

Exhaust Manifold

Hi RE fan :

have some question here:

my friend have exhaust manifold aka banana for FD. Can i use it in my FC engine ?

Thanks in advance.

Search

Enjoying Zerotohundred?

Log-in for an ad-less experience

Reply to thread

The Marketplace Latest

Mitsubishi lancer Evo x front bumper

Honda jazz fit gk flrs body kit

Proton S70 body kit

Proton saga BLM body kit

Perodua bezza ~accident repair

Mercedes Benz W205 C-class GT grille

BMW E90 ~brake caliper spray ~rim spray

Honda city gm6 FL front bumper

original rare spec Rays Volk Racing RE30 15x7jj...

original rare Rays Volk Racing TE37 SAGA S-Plus...

Posts refresh every 5 minutes

Recent Posts

Thrills and Spills at Zhuhai: Porsche Carrera Cup Asia Rounds 3 & 4 Recap

Proton Records High Demand for S70 with 1 Unit Booked every 4 minutes

Toyota Malaysia Enters Regional GT Racing with TGR Racing Malaysia

Home Win and Double Podium for Akash Nandy at Sepang Season Opener

Darker Design : Mercedes-Benz Launches GLA Nightfall Edition in Malaysia

Search

Online now

Enjoying Zerotohundred?