Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="DLegend" data-source="post: 811340" data-attributes="member: 2060">Decided to sounddeaden my Waja's boot during this semester break..... I already plastered the floor of the Waja with Dynamat Extreme, so I have only RM150 left. Here goes....Here are some pics to share:Hope this helps anyone who wants to try to DIY :)Materials:1. SikaDamp360 x3 pieces (limited budget) RM105.00 (supplier :boeytan)2. Insuflex (10mm x2) RM4x.00 (supplier :boeytan)3. Scissors & Penknife4. Dunlop CA Glue RM15 (big can)5. Whiteboard marker pen6. Old newspaper7. Vacuum cleaner8. Cold drinks RM3.00Here are the materials used:Silver pieces are SikaDamp630 & black mats are Insuflexhttp://i8.photobucket.com/albums/a46/DLegend/Materials.jpgFirst, strip the boot and vacuum it clean:(Note the Dynamat Extreme that was left over from the floor project)http://i8.photobucket.com/albums/a46/DLegend/Stripped.jpgNext, I placed the SikaDamp where i wanted to cover (exhaust noise) & cut it to shape :Remember to press it in place ( Use a heat source to soften the mat if required )http://i8.photobucket.com/albums/a46/DLegend/CuttingAndShaping.jpgThen, remove the backing paper and stick the SikaDamp to the surface with sufficient pressure:http://i8.photobucket.com/albums/a46/DLegend/FirstLayerSika.jpgUse the rest of the SikaDamp to cover the other important spots:http://i8.photobucket.com/albums/a46/DLegend/Sikadone.jpgAfter the SikaDamp's done, i used the old newspaper and drew out the shape to make templates for the Insuflex:http://i8.photobucket.com/albums/a46/DLegend/Shaping.jpgThen, cut the Insuflex according to the templates and apply Dunlop glue to the "rough" side of the mats and wait for the glue to harden slighty .... then STICK AWAY !!! :http://i8.photobucket.com/albums/a46/DLegend/Biginsuflex.jpgHere's when it's done: ( I left the higher portion un-matted because i'm gonna put my subbox there )http://i8.photobucket.com/albums/a46/DLegend/Finish.jpgHere are more pics of the Insuflex mats:http://i8.photobucket.com/albums/a46/DLegend/LeftDone.jpgBootlid dampened also:http://i8.photobucket.com/albums/a46/DLegend/TopBoot.jpgFinally, i cut another piece of Insuflex just to lay it on top of the dampened boot ( just before putting the floorboards back - no glue )http://i8.photobucket.com/albums/a46/DLegend/Final.jpgDon't forget to clean up the mess after finishing :)That's all for now, will do the doors next semester break.Results:1. Noticeable reduction in exhaust note intrusion2. More pronounced noise coming from engine portion (more work to be done)3. Whole car smells like glue for a week !!!4. Subwoofer hits harder and deeper... not sure why.:)Jay Jay.</blockquote>

Verification

The Marketplace Latest

Proton Preve R3 body kit
- Started by jeff6126
- Exterior and Body
Perodua Ativa gear up body kit
- Started by jeff6126
- Exterior and Body
BMW F10 Mperformance front skirt lip
- Started by jeff6126
- Exterior and Body
Honda Civic FC fk7si front bumper set
- Started by jeff6126
- Exterior and Body
brake caliper spray
- Started by jeff6126
- Exterior and Body
BMW F30 M3 bodykit/diffuser set
- Started by jeff6126
- Exterior and Body
Perodua Axia Rahmah bodykit
- Started by jeff6126
- Exterior and Body
Nissan Almera Tomei body kit
- Started by jeff6126
- Exterior and Body
original rare Black Racing Pro N1 16x6.5jj offset...
- Started by david tao
- Chassis and Wheels
original rare Rays Volk Racing TE37SL Black Edition...
- Started by david tao
- Chassis and Wheels

Posts refresh every 5 minutes

Aldolf Hitler pissed off at R35's Warranty

black evo 6 wgv 6133

hey brother...if this is ur car then i wanna say hi to u since i bump into u at federal highway this morning...was behind u wanted to see ur face and say hi but u know lah jam.......

Looking for TME(evo6.5) plate holder

delete........