Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="nan83" data-source="post: 3808974" data-attributes="member: 6718">yaa.. e6x can be operate in close loop.. stock narrowband o2 sensor can be use, just connect to haltech... if use plug & play hardness, no need to do wiring, just enable o2 close loop at halwinX software .. but need to configure it lah, such as target mV & etc.. if use hicam, cannot close loop at idle, so set min rpm tu 2000rpm.. coz tuning idle for hicam need a bit rich ..for the antilag system... it can be configure to be launch control or antilag... just do some configuration in halwinx it will effect differently..antilag setup:-connect a switch to AUX.IN (pin 28), this switch to activate antilag system-at halwinx, go to SETUP-->Input/Output Setup-->Aux in funtion = set to ANTILAG-Input-connect a solenoid valve to PWM.OUT4 (pin 24) . normally out4 free. if it have been use, change 1 or 2 or 3... but dun disable radiator fan control lah.. hehe ( solenoid valve is use to supply air to engine while throttle is close )-at halwinx, go to Options-->PWN & dig out option--> tick at PWM4 enable --> select Antilag Switch , than click properties.. enable zero tps only than configure retard ign value, % increase fuel & etc...-enjoy antilag system..For launch control-same as above just need to configure like below--at halwinx, go to Options-->PWN & dig out option--> tick at PWM4 enable --> select Antilag Switch , than click properties.. disable zero tps only than configure retard ign value, % increase fuel , On RPM ( put 5000rpm if wanna launch at that rpm) & etcanother function is flat shift (change gear while full throttle)-connect a clutch switch to AUX.IN (pin 28), this switch need to install at clutch paddle.. so when you press clutch, flat shift system will activate-at halwinx, go to SETUP-->Input/Output Setup-->Aux in funtion = set to flat shift-this no need to configure.. enjoy flat shift</blockquote>

Verification

The Marketplace Latest

HONDA CIVIC FL5 TYPE R 2.0 (M) 2025
- Started by rickyteoh2288
- Cars for sale
TOYOTA GR YARIS 1.6 (M) 2025 RZ High Performance
- Started by rickyteoh2288
- Cars for sale
HONDA CIVIC FL5 MUGEN PART 2024
- Started by rickyteoh2288
- Cars for sale
original rare Enkei ES Tarmac 15x7jj offset +35 4H...
- Started by david tao
- Chassis and Wheels
original rare Rays Volk Racing SE37 17x7.5jj offset...
- Started by david tao
- Chassis and Wheels
original rare Yokohama ADVAN Racing TC4 18x8.5...
- Started by david tao
- Chassis and Wheels
original rare Rays Volk Racing ZE40 17x9jj offset...
- Started by david tao
- Chassis and Wheels
original rare Rays Volk Racing INGS TS06 18x8jj...
- Started by david tao
- Chassis and Wheels
New original Defi Advance A1 NA package triple...
- Started by david tao
- Engine and Performance
original rare Rays Volk Racing CE28 16x7jj offset...
- Started by david tao
- Chassis and Wheels

Posts refresh every 5 minutes

Nangkang NS-2R Semi slick review?

Nankang NS-2R Semi slick, has anyone used this tyres... please share your experience...:wavey:

looking for a GTR34

i would like to purchase a r34 gtr with original condition. maybe minor modification also can. pls pm me if any

Cutting Evo 3 springs

I just installed an evo 3 spring + absorber (front and back) but the half cut shop gave me a wrong combination. The front is now around 6 1/2 fingers height and the back is only 2 fingers. Would there be any problems...