Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="georgecheng" data-source="post: 1582799" data-attributes="member: 15710">Bro, all piping is already done up only fit up. The only pipe that is to alter will be the down pipe to the exhaust. cause the end fitting does not fit well. Anyway, if you were me how do you feel. I driving a nissan B14, and have call them early and made an appointment on one of the wednesday to have my bolt on turbo and microtech lt8 to fit on my car. I have all, items, turbo, piping, intercooler, clutch, microtech, oil cooler, injector, fuel pump all to be fit to my ride. When, i drove down, i let them inspect the car and boss, keep, saying No problem can be done, hence I check with them all issuse, price and what i want them to do. I want all items to fit up, change to metal engine casket, and tuning. Price, they was set about 3k cause, they offer they will send piping for leak check, custom making the metal engine gasket, tunning, doing up the oil pan return line, install microtech and boost controller. Price not too sure too steep, but i feel a bit, anyway, if they do a good job, it's fine with me. Problem, first i checked with them and they mention they can rush out the job and give me the car on friday, so i go there on thur, they already start work, and have cut the slot for intercooler. Friday i go down, they mention they fit up the turbo and doing the clutch. Oil pan, was not done properly and was leaking. So they redo. Then I open the boot and found all clutch, injector, all items was not fit up. Hence i check with boss, and he mention, he thought, only fit up turbo, then no choice, i mention, i was all items to fit up. Hence friday can't pass me the car. Sat, I go down, car still not ready, he said microtech, can't run properly on my car. He don't have the diagram for my car. I no choice, go back, then call him, give him a week to find the detail. Then all the while, he give mention, aust can't provide him diagram, cause they main branch there have race, and no body can send him the pic. After, a week drag, he still can't fit it. Then just mention the car will run fine, even without the microtech. Then he offer to drive the car to me, cause he need go oversea, cause after his work he reached my area already 3plus am, so I just check with him how's the car. He said all installed. Problem one injector there can't sit properly, microtech, can't install, cause idling have problem, and boost control didn't install. Worst, metal gasket said, he take out and found can't fit and already do up with all sealant. I trust boss and he still quote 3.1k for it. I found quite exp and he mention he have done all these and that and this. I just paid him and expect he have done a really good job of this price.Problem i face during a week of car collection. 1) oil pan was still leaking, 2) the oil pan return pipe was done too long and the rubber piping connect to turbo was touching the exhast downpipe, he used heat wrap to prevent it burning, BUT just after a week, the pipe melt and engine oil burst out, leding me spend a sum on towing and repair. 3) exhaust down pipe was not done up properly, just connect and didn't see my center piping. Last week before, i go back, i told him to redo, and he didn't do at all. The center piping was touching the ground with I go over hump, and leding all my pipe damage after a week of use.4) Oil intercooler was install at my wheel well near bumper, and what u know the piping was from oil filter there, then under the alternator and go tru the wheel well, the piping was rubbing my tyres when I doing a U turn. 5) My fuel pump didn't even change yet.6) Next make me feel bad, is what, engine gasket didn't touch at all. Cause we should see the sealant or marking or sight of bolt taking out, but engine area was still the same. Yet there is a few more to go. I dont' wish to mention, I send him email with picture to prove what i say and have drop him SMS once every week to seek him to check the mail on this issue. Till now a month plus, still no reply. Guy, i believe, he still is a good tuner, but as workmanship, sorry, first time there really disappoint me. Moreover if you were me, think of it. Cause 3k to install a bolt on turbo without doing anything else. what u all FEEEL.</blockquote>

Verification

The Marketplace Latest

original rare Rays Volk Racing TE37 SAGA S-Plus...
- Started by david tao
- Chassis and Wheels
original Swift Springs rear strut bar set made in...
- Started by david tao
- Chassis and Wheels
Proton Preve R3 body kit
- Started by jeff6126
- Exterior and Body
Perodua Ativa gear up body kit
- Started by jeff6126
- Exterior and Body
BMW F10 Mperformance front skirt lip
- Started by jeff6126
- Exterior and Body
Honda Civic FC fk7si front bumper set
- Started by jeff6126
- Exterior and Body
brake caliper spray
- Started by jeff6126
- Exterior and Body
BMW F30 M3 bodykit/diffuser set
- Started by jeff6126
- Exterior and Body
Perodua Axia Rahmah bodykit
- Started by jeff6126
- Exterior and Body
Nissan Almera Tomei body kit
- Started by jeff6126
- Exterior and Body

Posts refresh every 5 minutes

Need help. Looking for Cast Turbo Manifold with T25 Flange for SXE10 3S-GE

Need help. Looking for Cast Turbo Manifold with T25 Flange for SXE10 3S-GE to fit GT2860R

Greddy Profec A and Rebic III

Any Sifus has or have experience in installing the Greddy Profec A and Rebic III???
Please call me at 016-3808883... Thank u!!!

How to write/spray/colour LETTER in TYRE

Hey...newbie here...any guide to whitening the tyre letters?
Yokohama,sumitomo, michelin... those Letter in WHITE colour which look the like the Original 4wd Tyres...Any comment? :) Any suggestion? as i know...those...