Diy : Superlon Installation

[ksgoh]

omg, i have been cheated by them.....must go back to complain them already...

 

[wira_se]

so ninja_iga wat glue is suitable to use?

 

[ninja_iga]

CA Glue or even SuperLon glue ;)

 

[ksgoh]

thanks for info.....any hardware got sell, right??

 

[Izso]

Stan, I've been looking around and found that the hot air was designed to escape through the bottom as u said, but that's assuming the car is moving. If stationary it doesn't move and gets trapped in the bonnet area.. so how do we fix that? With the Superlon it'll insulate and the engine bay will be quite hot for quite a while..

 

[evan2000]

lift up ur bonet.....a bit lah....

 

[ninja_iga]

that's why you've got a radiator fan for la..

 

[ky_fei]

is it cost rm50 for 4 doors for wira ? wanna buy it ledi..where t olet ppl stick it up ? any recomend? and how much the installation ?

 

[ksgoh]

where to buy?? cut in standard size already??

 

[ninja_iga]

Originally posted by ky_fei@Sep 7 2004, 01:56 PM
is it cost rm50 for 4 doors for wira ? wanna buy it ledi..where t olet ppl stick it up ? any recomend? and how much the installation ?

it costs about RM45 for 4 doors :)

RM5-10 for glue.

no precuts yet la :P

 

[NiCkY7]

ninja,

where's the page of the Superlon price liow ar?

i forget at where liow...

:P

 

[ninja_iga]

methinks first page kua

sold every 3ft x4ft :) (4ft is standard width, pls specify length, increment of every 3ft)

it's RM15 for 6mm
RM20 for 10mm

 

[ksgoh]

willing to buy, but sure dunno how to stick it on.....got user manual that show step by step??

 

[clsia1001]

Originally posted by ninja_iga@Aug 20 2004, 12:48 AM
yes that's correct.

BUT it's DESIGNED for the air to go underneath the car.

TELL me, where does the air go, with if it's not under?

..long time no on9....guess i cant on9 anymore.... :(
currently also on9 in college... :ph34r:

ninja,

I still think the heat will go up and the go out from the small holes on the bonnet.

if not, what for the holes design for, ..izzit? :lol:


juz my opinion B)

 

[ksgoh]

which hole??

 

[johnsonlam]

Originally posted by ksgoh@Sep 8 2004, 08:57 AM
willing to buy, but sure dunno how to stick it on.....got user manual that show step by step??

KsGoh...

It is in THIS thread lah the UserManual...
If it is not clear enough. Let me know.

 

[ninja_iga]

Originally posted by clsia1001+Sep 8 2004, 01:48 PM-->

QUOTE (clsia1001 @ Sep 8 2004, 01:48 PM)

--QuoteBegin-ninja_iga

@Aug 20 2004, 12:48 AM yes that's correct. BUT it's DESIGNED for the air to go underneath the car. TELL me, where does the air go, with if it's not under?

..long time no on9....guess i cant on9 anymore.... :( currently also on9 in college... :ph34r: ninja, I still think the heat will go up and the go out from the small holes on the bonnet. if not, what for the holes design for, ..izzit? :lol: juz my opinion B) [/b][/quote] abang clsia, what holes? tell me where other than Subaru WRX and Evo series, what other holes on bonnet!? why did manufacturer spend so much time researching and computer simulation hours to optimise the flow, to go BELOW the car??? dude, i do know my stuff. i've seen the simulation. heck, i've seen the heat charts too, blue for cold (relative) and red for the hottest (relative also) and every damn thing above the bonnet is BLUE! so tell me where all your hot air go? squeezing through those tiny holes? if you're saying the plastic grill near the windscreen, that the AiR-CON air-intake la! <_<

 

[ky_fei]

mr ninja ...how to buy from u ? and does any1 can teach me how to take off the door panel ??? thx.

 

[ninja_iga]

Originally posted by ky_fei@Sep 9 2004, 01:21 PM
mr ninja ...how to buy from u ? and does any1 can teach me how to take off the door panel ??? thx.

ky-fei

i'm located in Bandar Utama, Damansara area is best.

whats your quantity?

 

[ky_fei]

for wira 4 doors onli.. hope it can sound proft it .. hahahaha rm 45 rite ? i at kepong onli ma ~ :)