3sge Beam vs 4age Bt

hmmm i think i ever heard that there is ae110 with 4 wheel 3sgte. hehhe curious about it.

Installation charges different but what is the range .. because i did ask one about 4age transplant and he say just direct transplant only. dunno got check or overhaul and the cost is around RM1.5k
 
standard lor 1.5k ... ae101 with 4 wheel 3sgte yes thats possible .. anything is possible but its not street legal because you have to deal with the chassis to fit in the rear axle ... chassis modifications = illegal .. wont pass jpj inspection confirm ..
 
does installation fee of RM1.5k including top overhaul and checking of the gearbox
 
2ZZGE :adore: ,but market mods not so common. setup ITB's and 4-1 exhaust , you'll in paradise .:smokin:
 
Last edited:
usually rm1.5k is just the workmanship .. the parts are not included ..
 
2zzge also can fit .... the manual 6 speed .. whoa .. theres one ae92 trueno with 2zzge at my mech place .. 4th gear can reach 200kmph already ..

DAZ garage bro ? I think i saw ur car if it is. hahha.
 
lol yes daz garage .. stucked there for over 3 months .. slow progress .. wait until hand itchy already .. i always hang out there also .. have i seen you there ? @.@
 
3SGE beams redtop are either front wheel drive from the toyota celica or rear wheel drive in midship configuration of the toyota mr2 ..

the 3SGE beams blacktop comes in the toyota altezza/ lexus IS200.. rear wheel drive only ... 6 speed manual ..

the 3SGE blacktop beams into ae101 are quite a big project la cause need to change the engine from longitudinal to transverse .. the gearbox location and mounting all have to mod .. expensive lor ...
 
newer engine with vvti :proud:

---------- Post added at 08:00 PM ---------- 6 hour anti-bump limit - Previous post was at 07:58 PM ----------



thanks


if not mistaken, 2zzge need to modified engine mouting which JPJ will give troublesome..
 
if you want to use 2zzge in the AE chassis .. only need to fabricate custom bracket for the left side of the engine ... right side use back the old mounting .. as long as there is no welding done to the chassis, jpj wont kacau ... brakes la most important .. brake also need to upgrade if not sure fail ..

---------- Post added at 01:16 AM ---------- 6 hour anti-bump limit - Previous post was at 01:14 AM ----------

@2o2r

All these infos are shoved in my throat for quite sometime already ... about 2 years + lor .. graduated from the 3S engine already .. hahaha .. now lowest ranking spokesperson hehe ...
 
my vote goes to 4AGE BT..

lots can be done to the engine..

it can go up to 1950cc with a stroker kit

can put ARC induction box, Tom's intake, FGK extractor, Toda cam, standalone ECU

it can go more than 230 horsepower..

and get a 6speed gbox.. sure can tapau stock 3SGE after u've done all of the above.. :wink:

---------- Post added at 02:40 PM ---------- 6 hour anti-bump limit - Previous post was at 02:08 PM ----------

but if u lazy.. just get a 3SGE :wink:


bro zul,
as u mentioned, 4age bt can go up stroker kit to 1950cc? then using what type engine of stroker kit u mentioned? normally if not mistaken, 4age just can be transplant block 7afe.:proud:
 
bro zul,
as u mentioned, 4age bt can go up stroker kit to 1950cc? then using what type engine of stroker kit u mentioned? normally if not mistaken, 4age just can be transplant block 7afe.:proud:


actually it's a racing stroker kit from speed racer.. here's the website

http://www.speedracersportscars.com.au/

usually, they recommend 1900cc for daily use :wink:
 
actually it's a racing stroker kit from speed racer.. here's the website

http://www.speedracersportscars.com.au/

usually, they recommend 1900cc for daily use :wink:
haha,
i found this thread before ....but aftermarket malaysia got such thing to sell?
 

Similar threads

Posts refresh every 5 minutes




Search

Online now

Enjoying Zerotohundred?

Log-in for an ad-less experience